View STR-W6765_3000142.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STR-W6765 description the STR-W6765 is a quasi-resonant topology ic designed for smps applications. it shows lower emi noise characteristics than conventional pwm solutions, especially at greater than 2 mhz. it also provides a soft-switching operation to turn on the internal mosfet at close to zero voltage (v ds bottom point) by use of the resonant characteristic of primary inductance and a resonant capacitor. the package is a fully molded to-220, which contains the controller chip (mic) and mosfet, enabling output power up to 52 w with universal input or 110 w with a 230 vac input. the bottom-skip function skips the first bottom of v ds and turns on the mosfet at the second bottom point, to minimize an increase of operational frequency at light output load, improving system-level efficiency over the entire load range. there are two standby functions available to reduce the input power under very light load conditions. the first is an auto-burst mode operation that is internally triggered by periodic sensing, and the other is a manual standby mode, which is executed by clamping the secondary output. in general applications, the manual standby mode reduces the input power further compared to the auto-burst mode. the soft-start function minimizes surge voltage and reduces power stress to the mosfet and to the secondary rectifying quasi-resonant topology primary switching regulators typical application package: 6-pin to-220 continued on the next page? 28103.30-6 features and benefits ? quasi-resonant topology ic ? low emi noise and soft switching ? bottom-skip operation ? improved system efficiency over the entire output load by avoiding increase of switching frequency ? standby burst mode operation ? lowers input power at very light output load condition ? avalanche-guaranteed mosfet ? improves system- level reliability and does not require v dss derating ? 800 v / 1.8 , 52 to 110 w (universal/230 vac input) continued on the next page? +b gnd s1 p d d s/gnd v cc s2 lowb gnd for erramp, sanken se series device recommended for si, sanken linear regulator ic recommended 1 1 3 3 7 7 cont str-w6735 6 6 ocp /bd 4 4 fb rocp erramp ss /olp 5 5 standby on/off standby out cx rx si a b b a
quasi-resonant topology primary switching regulators STR-W6765 2 features and benefits (continued) selection guide part number package packing STR-W6765 to-220 bulk, 100 pieces all performance characteristics given are typical values for circuit or system baseline design only and are at the nominal operating voltage and an ambient temperature of +25c, unless oth er wise stated. ? various protections ? improved system-level reliability ? pulse-by-pulse drain overcurrent limiting ? overvoltage protection (bias winding voltage sensing), with latch ? overload protection with latch ? maximum on-time limit diodes during the start-up sequence. various protections such as overvoltage, overload, overcurrent, maximum on-time protections and avalanche-energy-guaranteed mosfet secure good system- level reliability. applications include the following: ? set top box ? lcd pc monitor, lcd tv ? printer, scanner ? smps power supplies description (continued) absolute maximum ratings at t a = 25c parameter symbol terminal conditions rating unit drain current 1 i d peak 1 - 3 single pulse 11.2 a maximum switching current 2 i dmax 1 - 3 t a = ?20c to 125c 11.2 a single pulse avalanche energy 3 e as 1 - 3 single pulse, v dd = 99 v, l = 20 mh, i lpeak = 5.8 a 300 mj input voltage for controller (mic) v cc 4 - 3 35 v ss/olp terminal voltage v ssolp 5 - 3 ?0.5 to 6.0 v fb terminal inflow current i fb 6 - 3 10 ma fb terminal voltage v fb 6 - 3 i fb within the limits of i fb ?0.5 to 9.0 v ocp/bd terminal voltage v ocpbd 7 - 3 ?1.5 to 5.0 v mosfet power dissipation 4 p d1 1 - 3 with infinite heatsink 28.7 w without heatsink 1.3 w controller (mic) power dissipation p d2 4 - 3 v cc i cc 0.8 w operating internal leadframe temperature t f ? refer to t op ?20 to 115 c operating ambient temperature t op ? ?20 to 115 c storage temperature t stg ? ?40 to 125 c junction temperature t j ? 150 c 1 refer to figure 2 2 i dmax is the drain current determined by the drive voltage of the ic and the threshold voltage, v th , of the mosfet 3 refer to figure 3 4 refer to figure 5 allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 3 temperature, t f (c) safe operating area temperature derating coefficient (%) 0 20 40 60 80 100 0 25 50 75 100 125 150 drain-to-source voltage, v ds (v) drain current, i d (a) 11.2 1.0 10.0 0.1 100.0 10 100 1000 1 1 ms 0.1 ms current limit due to r ds(on) refer to figure 1 for mosfet soa temperature derating coefficient figure 1 ? mosfet safe operating area derating curve figure 2 ? mosfet safe operating area drain current versus voltage at t a = 25c, single pulse d s/gnd ocp/bd v cc fb start stop burst r s q reg& iconst ovp drive reg protection latch s r q fb ocp bsd bd bottom selector counter ss/olp olp delay s r q osc maxon soft start burst control burst control 4 + - + - + - + - + - + - 1 3 6 7 5 number name description functions 1 d drain mosfet drain 2 nc clipped no connection 3 s/gnd source/ground terminal mosfet source and ground 4 vcc power supply terminal input of power supply for control circuit 5 ss/olp soft start/overload protection terminal input to set delay for overload protection and soft start operation 6 fb feedback terminal input for constant voltage control and burst (intermittant)mode oscillation cotnrol signals 7 ocp/bd overcurrent protection/bottom detection input for overcurrent detection and bottom detection signals allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 4 channel junction temperature, t j (c) e as temperature derating coefficient (%) 0 20 40 60 80 100 25 50 75 100 125 150 time, t (s) transient thermal resistance, r q jc (c/w) 0.001 0.010 0.100 1.000 10.000 100 10 10m 1m 100m 1 ambient temperature, t a (c) power dissipation, p d1 (w) 0 5 10 15 20 25 30 0 20 40 60 80 100 120 140 160 p d1 = 1.3 w at t a ??& without heatsink with infinite heatsink p d1 = 28.7 w at t a ??& figure 3 ? mosfet avalanche energy derating curve figure 4 ? transient thermal resistance figure 5 ? mosfet power dissipation versus temperature allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 5 electrical characteristics characteristic symbol terminals min. typ. max. units electrical characteristics for controller (mic) 1 , valid at t a = 25c, v cc = 20 v, unless otherwise specified power supply start-up operation operation start voltage v cc(on) 4 - 3 16.3 18.2 19.9 v operation stop voltage v cc(off) 4 - 3 8.8 9.7 10.6 v circuit current in operation i cc(on) 4 - 3 ? ? 6 ma circuit current in non-operation i cc(off) 4 - 3 ? ? 100 a oscillation frequency f osc 1 - 3 19 22 25 khz soft start operation stop voltage v ssolp(ss) 5 - 3 1.1 1.2 1.4 v soft start operation charging current i ssolp(ss) 5 - 3 ?710 ?550 ?390 a normal operation bottom-skip operation threshold voltage 1 v ocpbd(bs1) 7 - 3 ?0.720 ?0.665 ?0.605 v bottom-skip operation threshold voltage 2 v ocpbd(bs2) 7 - 3 ?0.485 ?0.435 ?0.385 v overcurrent detection threshold voltage v ocpbd(lim) 7 - 3 ?0.995 ?0.940 ?0.895 v ocp/bdocp/bd terminal outflow current i ocpbd 7 - 3 ?250 ?100 ?40 a quasi-resonant operation threshold voltage 1 v ocpbd(th1) 7 - 3 0.28 0.40 0.52 v quasi-resonant operation threshold voltage 2 v ocpbd(th2) 7 - 3 0.67 0.80 0.93 v fb terminal threshold voltage v fb(off) 6 - 3 1.32 1.45 1.58 v fb terminal inflow current (normal operation) i fb(on) 6 - 3 600 1000 1400 a standby operation standby operation start voltage v cc(s) 4 - 3 10.3 11.1 12.1 v standby operation start voltage interval v cc(sk) 4 - 3 1.10 1.35 1.65 v standby non-operation circuit current i cc(s) 4 - 3 ? 20 56 a fb terminal inflow current, standby operation i fb(s) 6 - 3 ? 4 14 a fb terminal threshold voltage, standby operation v fb(s) 6 - 3 0.55 1.10 1.50 v minimum on time t on(min) 1 - 3 0.40 0.82 1.25 s maximum on time t on(max) 1 - 3 27.5 32.5 39.0 s protection operation overload protection operation threshold voltage v ssolp(olp) 5 - 3 4.0 4.9 5.8 v overload protection operation charging current i ssolp(olp) 5 - 3 ?16 ?11 ?6 a overvoltage protection operation voltage v cc(ovp) 4 - 3 25.5 27.7 29.9 v latch circuit holding current 2 i cc(h) 4 - 3 ? 45 140 a latch circuit release voltage 2 v cc(la.off) 4 - 3 6.0 7.2 8.5 v electrical characteristics for mosfet , valid at t a = 25c, unless otherwise specified drain-to-source breakdown voltage v dss 1 - 3 800 ? ? v drain leakage current i dss 1 - 3 ? ? 300 a on resistance r ds(on) 1 - 3 ? ? 1.8 switching time t f 1 - 3 ? ? 400 ns thermal resistance r ja junction to internal frame ? ? 1.55 c/w 1 current polarity with respect to the ic: positive current indicates current sink at the terminal named, negative current indica tes source at the terminal named. 2 latch circuit refers to operation during overload protection or overvoltage protection. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 6 electrical characteristics test conditions* parameter test conditions v cc (v) measure- ment circuit operation start voltage vcc voltage at which oscillation starts. 0 20 1 operation stop voltage vcc voltage at which oscillation stops. 20 8.8 circuit current in operation inflow current flowing into power supply terminal in oscillation. 20 circuit current in non-operation inflow current flowing into power supply terminal prior to oscillation. 15 oscillation frequency oscillating frequency ( f osc = 1 / t ). 20 soft start operation stop voltage ss/olp terminal voltage at which iss/olp reach ?100 a by raising the ss/olp terminal voltage from 0 v gradually. 20 5 soft start operation charging current ss/olp terminal charging current (ss/olp terminal voltage = 0 v). bottom-skip operation threshold voltage 1 input 1 s pulse width, as shown in waveform 1, to ocp/bd terminal twice after v 1-3 rises. after that, offset the input waveform gradually from 0 v in the minus direction. measurment of the offset voltage v ocpbd(bs1) is taken when the v 1-3 start-to-fall point switches from two- pulses-after to one-pulse-after. 20 3 bottom-skip operation threshold voltage 2 after measuring v ocpbd(bs1) , as shown in waveform 2, offset the input waveform gradually. measurment of the offset voltage v ocpbd(bs2) is taken when the v 1-3 start-to-fall point switches from two-pulses-after to one-pulse-after. overcurrent detection threshold voltage ocp/bd terminal voltage at which oscillation stops by lowering the ocp/bd terminal voltage from 0 v gradually. 20 2 ocp/bdocp/bd terminal outflow current ocp/bd terminal outflow current (ocp/bd terminal voltage = ?0.95 v). quasi-resonant operation threshold voltage 1 ocp/bd terminal voltage at which oscillation starts with setting the ocp/bd terminal voltage at 1 v, and then lowering the voltage gradually. quasi-resonant operation threshold voltage 2 ocp/bd terminal voltage at which oscillation stops by raising the ocp/bd terminal voltage from 0 v gradually. fb terminal threshold voltage fb terminal voltage at which oscillation stops by raising the fb terminal voltage from 0 v gradually. 20 4 fb terminal inflow current (normal operation) fb terminal inflow current (fb terminal voltage = 1.6 v). 20 standby operation start voltage v cc voltage at which i cc reaches 1 ma (fb terminal voltage = 1.6 v). 0 15 standby operation start voltage interval specified by v cc(sk) = v cc(s) ? v cc(off) .? standby non-operation circuit current inflow current flowing into power supply terminals prior to oscillation (fb terminal voltage = 1.6 v). 10.2 fb terminal inflow current, standby operation fb terminal inflow current (fb terminal voltage = 1.6 v). 10.2 fb terminal threshold voltage standby operation fb terminal voltage at which oscillation starts by raising the fb terminal voltage from 0 v gradually. 15 minimum on time waveform between terminals 1 and 3 at low. 20 6 maximum on time waveform between terminals 1 and 3 at low. 20 1 continued on the next page? allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 7 electrical characteristics test conditions*, continued parameter test conditions v cc (v) measure- ment circuit overload protection operation threshold voltage ss/olp terminal voltage at which oscillation stops. 20 5 overload protection operation charging current ss/olp terminal charging current (ss/olp terminal voltage = 2.5 v). ? overvoltage protection operation voltage v cc voltage at which oscillation stops. 0 30 1 latch circuit holding current inflow current at v cc(off) ? 0.3; after ovp operation. v cc(off) ? 0.3 latch circuit release voltage v cc voltage at which i cc reaches 20 a or lower by decreasing v cc after ovp operation. 30 6 drain-to-source breakdown voltage i dss = 300 a ? 7 drain leakage current v dss = 800 v ? single pulse avalanche energy ? 30 8 on-resistance i ds = 1.4 a 20 9 switching time ? 20 1 *oscillating operation is specified with a rectangular waveform between terminals 1 and 3. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 8 9y 9? 9 99a9? a a 10v 100 ? t 4.7k v cc i cc t on v v 10 9? 90 9? tf ds/gndvcc ss/olp fb ocp/bd 50 9? 0.1 ? f 9y 9? 9 99a9? 10v 100 4.7k v cc 20v ds/gndvcc ss/olp fb ocp/bd 0.1 ? f 9y 9? 9 99a9? 10v 100 4.7k v cc 20v ds/gndvcc ss/olp fb ocp/bd 0.1 ? f measurement circuit 1 measurement circuit 2 measurement circuit 3 allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 9 measurement circuit 4 measurement circuit 6 measurement circuit 5 9y 9? 9 99a9? a a 10v 100 4.7k v cc v v d s/gnd vcc ss/olp fb ocp/bd 0.1 ? f a a v v 9y 9? 9 99a9? 10v 100 v cc 20v ds/gndvcc ss/olp fb ocp/bd a a v v 9y 9? 9 99a9? 10v 100 4.7k v cc 20v d s/gnd vcc ss/olp fb ocp/bd 0.1 ? f t on 9? min 9? 9v osc1 v1-3 5v osc1 200 :* 500ns allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 10 9y 9?999a9? mosfet mosfet measuring equipment v dss i dss d s/gnd vcc ss/olp fb ocp/bd avalanche energy tester i l v ds 9y 9? 9 99a9? v cc ds/gndvcc ss/ olp fb oc p/ bd t1 v dspeak v dd i l 0 30v v cc 0 v ds ? i ds 9y 9? 9 99a9? 0.1 ? f ds/gndvcc ss/olp fb ocp/bd 4.7k r ds(on)= v ds(on)/ i ds 20v v ds(on) measurement circuit 7 measurement circuit 9 measurement circuit 8 dd ds ds as v peak v peak v i l peak l e ? ? ? 2 2 1 equation for calculation of avalanche engery, e as ; to be adjusted for i l peak = 5.8 a allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 11 v ds v ocp/bd gnd v ocpbd(bs1) v ocpbd(bs2) gnd v ds v ocp/bd waveform 2 waveform 1 allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 12 package dimensions, to-220 10.0 0.2 4.2 0.2 2.8 0.2 ?3.2 0.2 2.6 0.1 (2r1) terminal dimension at case surface 5.08 0.6 1.74 +0.2 C0.1 1.34 +0.2 C0.1 0.45 +0.2 C0.1 16.9 0.3 10.4 0.5 5.0 0.5 7.9 0.2 4 0.2 2.8 max (5.4) gate burr branding xxxxxxxx xxxxxxxx gate burr: 0.3 mm (max.) terminal core material: cu terminal treatment: ni plating and solder dip heat sink material: cu heat sink treatment: ni plating leadform: 2003 weight (approximate): 2.3 g dimensions in millimeters drawing for reference only branding codes (exact appearance at manufacturer discretion): 1st line, type: w6765 2nd line, lot: ymdd r where: y is the last digit of the year of manufacture m is the month ( 1 to 9, o, n, d ) dd is the 2-digit date r is the manufacturer registration symbol 1234567 terminal dimensions at case surface 6p1.27 0.15 = 7.62 0.15 terminal dimension at lead tips allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 13 packing specifications minimum packing option: tube fm-205 e shipping tube dimensions: wall thickness: 0.60.3 mm wall warp: <2 mm material: hardened polyvinyl coating: antistatic tolerance 0.4 mm, unless otherwise specified all dimensions: mm side marked antistatic (3.6) (15.4) 9 r0.6 5.1 2.85 14.3 8.9 35.0 1.4 9.5 +0.3 C0.1 4.8 +0.4 0 1.3 +0.3 C0.2 shipping carton dimensions: capacity: 1800 pieces maximum per carton 36 tubes per carton 3 rows, 12 tubes per row spacer carton (side view) spacer tube 6 2 0 125 1 8 5 tube allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 14 because reliability can be affected adversely by improper storage environments and handling methods, please observe the followi ng cautions. cautions for storage ? ensure that storage conditions comply with the standard temperature (5c to 35c) and the standard relative humidity (around 40 to 75%); avoid storage locations that experience extreme changes in temperature or humidity. ? avoid locations where dust or harmful gases are present and avoid direct sunlight. ? reinspect for rust in leads and solderability of products that have been stored for a long time. cautions for testing and handling when tests are carried out during inspection testing and other standard test periods, protect the products from power surges f rom the testing device, shorts between adjacent products, and shorts to the heatsink. remarks about using silicone grease with a heatsink ? when silicone grease is used in mounting this product on a heatsink, it shall be applied evenly and thinly. if more silicone gr ease than required is applied, it may produce stress. ? volatile-type silicone greases may produce cracks after long periods of time, resulting in reduced heat radiation effect. silic one grease with low consistency (hard grease) may cause cracks in the mold resin when screwing the product to a heatsink. ? our recommended silicone greases for heat radiation purposes, which will not cause any adverse effect on the product life, are indicated below: type suppliers g746 shin-etsu chemical co., ltd. yg6260 ge toshiba silicone co., ltd. sc102 dow corning toray silicone co., ltd. soldering ? when soldering the products, please be sure to minimize the working time, within the following limits: 2605c 10 s 3505c 3 s ? soldering iron should be at a distance of at least 1.5 mm from the body of the products electrostatic discharge ? when handling the products, operator must be grounded. grounded wrist straps worn should have at least 1 m of resistance to ground to prevent shock hazard. ? workbenches where the products are handled should be grounded and be provided with conductive table and floor mats. ? when using measuring equipment such as a curve tracer, the equipment should be grounded. ? when soldering the products, the head of soldering irons or the solder bath must be grounded in other to prevent leak voltage s generated by them from being applied to the products. ? the products should always be stored and transported in our shipping containers or conductive containers, or be wrapped in al uminum foil. assembly ? during soldering or other operations, the interior frame temperature of the device should never exceed 105c. ? recommended screw torque through the mounting tab is 0,588 to 0.785 n ? m (6 to 8 kgf ? cm) warning ? these devices are designed to be operated at lethal voltages and energy levels. circuit designs that embody these components must conform with applicable safety requirements. pre cau tions must be taken to prevent accidental contact with power-line potentials. do not connect ground ed test equipment. the use of an isolation transformer is recommended during circuit development and breadboarding. allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com
quasi-resonant topology primary switching regulators STR-W6765 15 the products described herein are manufactured in ja pan by sanken electric co., ltd. for sale by allegro microsystems, inc. sanken and allegro reserve the right to make, from time to time, such de par tures from the detail spec i fi ca tions as may be re quired to per mit im- prove ments in the per for mance, reliability, or manufacturability of its prod ucts. therefore, the user is cau tioned to ve rify that the in for ma tion in this publication is current before placing any order. when using the products described herein, the ap pli ca bil i ty and suit abil i ty of such products for the intended purpose shall be reviewed at the users responsibility. although sanken undertakes to enhance the quality and reliability of its prod ucts, the occurrence of failure and defect of sem i con duc tor products at a certain rate is in ev i ta ble. users of sanken products are requested to take, at their own risk, preventative measures including safety design of the equipme nt or systems against any possible injury, death, fires or damages to society due to device failure or malfunction. sanken products listed in this publication are designed and intended for use as components in general-purpose electronic equip ment or apparatus (home ap pli anc es, office equipment, tele com mu ni ca tion equipment, measuring equipment, etc.). their use in any applicat ion requiring radiation hardness assurance (e.g., aero space equipment) is not supported. when considering the use of sanken products in ap pli ca tions where higher reliability is re quired (transportation equipment and its control systems or equip ment, fire- or burglar-alarm systems, various safety devices, etc.), contact a company sales representative to discuss and obtain written confirmation of your spec i fi ca tions. the use of sanken products without the written consent of sanken in applications where ex treme ly high reliability is required (aerospace equip- ment, nuclear power-control stations, life-support systems, etc.) is strictly prohibited. the information in clud ed herein is believed to be accurate and reliable. ap pli ca tion and operation examples described in this pub li ca tion are given for reference only and sanken and allegro assume no re spon si bil i ty for any in fringe ment of in dus tri al property rights, intellectual property rights, or any other rights of sanken or allegro or any third party that may result from its use. copyright ? 2006 allegro microsystems, inc. this datasheet is based on sanken datasheet sse-22774 allegro microsystems, inc. 115 northeast cutoff, box 15036 worcester, massachusetts 01615-0036 (508) 853-5000 www.allegromicro.com

▲Up To Search▲

Price & Availability of STR-W6765

	To Download STR-W6765 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .